分享硬件，软件，材料， 化学等原创内容
Cisco Packet Tracer校园网建设
网络通讯
Cisco Packet Tracer校园网建设
网络通讯

Cisco Packet Tracer校园网建设

先规划并标记好vlan划分，然后配置服务器，最后配置终端PC

1. 服务器接入路由器配置

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 192.168.8.5 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int f0/1
Router(config-if)#ip add 192.168.9.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#ip helpe
Router(config-if)#ip helper-address 192.168.8.3 //dhcp服务器地址
Router(config-if)#ex

Router(config)#router rip  //配置rip路由协议
Router(config-router)#v 2  //version 2, rip version 2
Router(config-router)#no au //no autosummary 关闭rip自动汇总
Router(config-router)#net 192.168.8.0
Router(config-router)#net 192.168.9.0
Router(config-router)#

2. 出口路由器配置

Router>no
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 192.168.9.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int f0/1
Router(config-if)#ip add 192.168.10.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#ip helper-address 192.168.8.3
Router(config-if)#int s0/3/0 //f0/0是快速以太网接口，用RJ45水晶头连接, Serial0/0是串行接口，用V35线来传输数据，是同步的，需要DCE同步时钟频率
Router(config-if)#ip add 100.1.1.1 255.255.255.0
Router(config-if)#clock rate 64000 //DCE线缆(信号电缆-V.24串口电缆),同步时钟频率
Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial0/3/0, changed state to down
Router(config-if)#int f0/0
Router(config-if)#ip nat inside (nat: network address transition, 内网地址转换，通过映射,让外网可以访问内网的地址
Router(config-if)#int f0/1
Router(config-if)#ip nat inside
Router(config-if)#int s0/3/0
Router(config-if)#ip nat outside
Router(config-if)#ex
Router(config)#ip nat pool DZC 100.1.1.3 100.1.1.10 netmask 255.255.255.0 //配置转换地址池
Router(config)#access-list 1 permit 192.168.0.0 0.0.255.255 //允许访问internet从192.168.0.0到192.168.255.255, 通过反掩码
Router(config)#ip nat inside source list 1 pool DZC //建立动态源转换，源list1的IP段转换为地址池 SZC的IP段
Router(config)#router rip
Router(config-router)#v 2
Router(config-router)#no au
Router(config-router)#net 192.168.9.0
Router(config-router)#net 192.168.10.0
Router(config-router)#default-information originate //在rip中，默认路由器采用default-information originate 方式向其他路由器注入
Router(config-router)#ex
Router(config)#ip route 0.0.0.0 0.0.0.0 100.1.1.2 //缺省路由,下一跳路由
Router(config)#

3.外网路由器配置

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip  add 100.1.2.1 255.255.255.0
Router(config-if)#int f0/1
Router(config-if)#ip  add 100.1.3.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#int f0/0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int s0/3/0
Router(config-if)#ip add 100.1.1.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up

4.核心路由器配置

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 192.168.10.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int f0/1
Router(config-if)#ip add 192.168.12.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ip helper-address 192.168.8.3
Router(config-if)#int f1/0
Router(config-if)#ip add 192.168.13.1 255.255.255.0
Router(config-if)#ip helper-address 192.168.8.3
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#int s0/3/0 //此处为非时钟一侧，不需要配置串口同步时钟
Router(config-if)#ip add 192.168.11.1 255.255.255.0 
Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial0/3/0, changed state to down
Router(config-if)#ip helper-address 192.168.8.3
Router(config-if)#ex
Router(config)#router rip
Router(config-router)#v 2
Router(config-router)#no au
Router(config-router)#net 192.168.10.0
Router(config-router)#net 192.168.11.0
Router(config-router)#net 192.168.121.0
Router(config-router)#no net 192.168.121.0 //输错，no掉
Router(config-router)#net 192.168.12.0
Router(config-router)#net 192.168.13.0
Router(config-router)#

5. 分校区接入路由器

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config-if)#int f0/0
Router(config-if)#ip add 192.168.7.254 255.255.255.0
Router(config-if)#no sh
Router(config-if)#int s0/3/0
Router(config-if)#ip add 192.168.11.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/3/0, changed state to up

Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed state to up

Router(config-if)#ex
Router(config)#router rip
Router(config-router)#v 2
Router(config-router)#no au
Router(config-router)#net 192.168.7.0
Router(config-router)#net 192.168.11.0
Router(config-router)#

6. 核心交换机配置

Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#vlan 30
Switch(config-vlan)#vlan 40
Switch(config-vlan)#vlan 50
Switch(config-vlan)#vlan 60
Switch(config-vlan)#ex
Switch(config)#int vlan 10
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan10, changed state to up

Switch(config-if)#ip add 192.168.1.1 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#int vlan 20
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changed state to up

Switch(config-if)#ip add 192.168.2.1 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#int vlan 30
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up

Switch(config-if)#ip add 192.168.3.1 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#int vlan 40
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan40, changed state to up

Switch(config-if)#ip add 192.168.4.1 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#int vlan 50
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan50, changed state to up

Switch(config-if)#ip add 192.168.5.1 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#int vlan 60
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan60, changed state to up

Switch(config-if)#ip add 192.168.6.254 255.255.255.0
Switch(config-if)#ip helper-address 192.168.8.3
Switch(config-if)#ex
Switch(config)#int vlan 19
Switch(config-if)#int vlan 10
Switch(config-if)#ex
Switch(config)#int vlan 10
Switch(config-if)#standby 10 ip 192.168.1.254
Switch(config-if)#standby 10 priority 101
Switch(config-if)#standby 10 preempt
Switch(config-if)#standby 10 track f0/1

Switch(config)#int vlan 20
Switch(config-if)#standby 20 ip 192.168.2.254
Switch(config-if)#standby 20 priority 101
Switch(config-if)#standby 20 preempt
Switch(config-if)#standby 20 track f0/1
Switch(config-if)#int vlan 30
Switch(config-if)#standby 30 ip 192.168.3.254
Switch(config-if)#int vlan 40
Switch(config-if)#standby 40 ip 192.168.4.254
Switch(config-if)#int vlan 50
Switch(config-if)#standby 50 ip 192.168.5.254
Switch(config-if)#ex
Switch(config)#ip routing
Switch(config)#int f0/1
Switch(config-if)#no sw
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan20 Grp 20 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan20 Grp 20 state Standby -> Active

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#ip add 192.168.12.2 255.255.255.0
Switch(config-if)#no sh
Switch(config-if)#int f0/7
Switch(config-if)#sw mo acc
Switch(config-if)#sw mo access 
Switch(config-if)#sw ac vlan 60
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan60, changed state to up

Switch(config-if)#ex
Switch(config)#int f0/2
	
Switch(config-if)#sw tr encapsulation dot1q
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan40, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan50, changed state to up

Switch(config-if)#int f0/3
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan50 Grp 50 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan30 Grp 30 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan30 Grp 30 state Standby -> Active

%HSRP-6-STATECHANGE: Vlan50 Grp 50 state Standby -> Active

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#sw tr encapsulation dot1q
%HSRP-6-STATECHANGE: Vlan20 Grp 20 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan20 Grp 20 state Standby -> Active

Switch(config-if)#sw tr encapsulation dot1q
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan40 Grp 40 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan40 Grp 40 state Standby -> Active

Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up

Switch(config-if)#int f0/4
Switch(config-if)#sw tr encapsulation dot1q
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

Switch(config-if)#int f0/5
Switch(config-if)#sw tr encapsulation dot1q
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to up

Switch(config-if)#int f0/6
Switch(config-if)#sw tr encapsulation dot1q
Switch(config-if)#int f0/6
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/6, changed state to up

Switch(config-if)#ex
Switch(config)#router rip
Switch(config-router)#v 2
Switch(config-router)#no
% Incomplete command.
Switch(config-router)#no au
Switch(config-router)#net 192.168.1.0
Switch(config-router)#net 192.168.2.0
Switch(config-router)#net 192.168.3.0
Switch(config-router)#net 192.168.4.0
Switch(config-router)#net 192.168.5.0
Switch(config-router)#net 192.168.6.0
Switch(config-router)#net 192.168.12.0
Switch(config-router)#

7. 核心交换机2配置


                                  ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#standby 50 preemspt
                                  ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#standby 50 preempt
Switch(config-if)#
 %HSRP-6-STATECHANGE: Vlan50 Grp 50 state Standby -> Active

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#
Switch(config-if)#
Switch(config-if)#
Switch(config-if)#int vlan 59d
                   ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#standby 50 preemspt
%HSRP-6-STATECHANGE: Vlan10 Grp 10 statstandby 40 preemspt
%HSRP-6-STATECHANGE: Vlan10 Grp 10 stateint vlan 50d
                   ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#standby
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby
 
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
50 track f0/1
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#ex
Switch(config)#ip r
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby
outi
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
ng
Switch(config)#int f0/1
Switch(config-if)#no sw
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
ip add ip address 1
%HSRP-6-STATECHANGE: Vlan40 Grp 40 state Standby -> Active
92.168/1
%HSRP-6-STATECHANGE: Vlan30 Grp 30 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan30 Grp 30 state Standby -> Active

                         ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#ip add ip address 192.168/1
%HSRP-6-STATECHANGE: Vlan50 Grp 50 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan50 Grp ip add ip address 192.168/1
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 
Switch(config-if)#
Switch(config-if)#
Switch(config-if)#ip add ip address 192.168.13.2 255.255.255.0
                         ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
ip add ip address 192.168.13.2 255.255.255.0
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

                         ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#
Switch(config-if)#
Switch(config-if)#ip add ip address 192.168.13.2 255.255.255.0
                         ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
d ip address 192.168.13.2 255.255.255.0
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE:ip address 192.168/1
                             ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#ip address 192.168.13.2 255.255.255.0
Switch(config-if)#no sh
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#int f
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
0/2
Switch(config-if)#sw tr en
Switch(config-if)#sw tr encapsulation  dot1q
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#sw mo tr
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby
int
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
 f0/3
Switch(config-if)#sw tr encapsulation  dot1q
Switch(config-if)#sw mo tr
Switch(config-if)#int f0/4
Switch(config-if)#sw tr encapsulation  dot1q\
                                            ^
% Invalid input detected at '^' marker.
	
Switch(config-if)#sw tr encapsulation  dot1q
Switch(config-if)#sw mo tr
Switch(config-if)#int f0/5
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#sw tr encapsulation  dot1q
Switch(config-if)#sw mo tr
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#int f0/5
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
6
Switch(config-if)#int f0/6
Switch(config-if)#sw tr encapsulation  dot1q
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

Switch(config-if)#sw mo tr
Switch(config-if)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
ex
Switch(config)#router rip
Switch(config-router)#v 2
Switch(config-router)#no au
Switch(config-router)#net 192.168.
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby
1
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
.0
Switch(config-router)#net 192.168.2.0
Switch(config-router)#net 192.168.3.0
Switch(config-router)#net 192.168.4.0
Switch(config-router)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active
net 192.168.5.0
Switch(config-router)#net 192.168.13.0
Switch(config-router)#
%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Speak -> Standby

%HSRP-6-STATECHANGE: Vlan10 Grp 10 state Standby -> Active

8. 二层交换机0配置：

Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#ex
Switch(config)#int f0/1
Switch(config-if)#sw mo tr
Switch(config-if)#int f0/4
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

Switch(config-if)#int f0/2
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 10
Switch(config-if)#int f0/3
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 10
Switch(config-if)#vlan 10
Switch(config-vlan)#

9. 二层交换机1~6配置：

Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 20
Switch(config-vlan)#ex
Switch(config)#int f0/1
Switch(config-if)#sw mo tr
Switch(config-if)#int f0/4
Switch(config-if)#sw mo tr

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

Switch(config-if)#int f0/2
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 20
Switch(config-if)#int f0/3
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 20
Switch(config-if)#vlan 20

10. 无线路由器和移动终端配置

11. dhcp配置：

12. dns服务器配置


13. web http服务器

14. ftp服务器配置

发表评论

您的电子邮箱地址不会被公开。